Snapper7 75mm Micro FPV Racer Quadcopter (Frsky Receiver Edition)

Main Features:
● Multi-flight modes to choose: macro / AIR / ANGLE
● Powerful brushless motor and ESC
● CNC aluminum alloy propeller guard
● BetaFlight OSD to get RSSI, voltage and other information from your goggles
● Use OSD to adjust the flight controller settings and the PID
● The Frsky version supports both EU LBT and NON-EU Frsky transmitter
● Full telemetry function ready
● Head lights ready
● Adjustable camera angle
● Real Bind and Fly version

Snapper7 75mm Micro FPV Racer Quadcopter (Frsky Receiver Edition)

Wheelbase: 75mm
Propeller: 40mm 3 - blade propeller ( 4 CW + 4 CCW )

Crazybee F3 Flight Controller
Firmware: Crazybee BetaFlight 3.3.0
MCU: STM32F303CCT6 ( 72MHz, 256K flash )
Sensor: MPU6000 ( SPI connection )
Power supply: 1S battery input ( DC 3.5 - 4.35V )
Built-in 5A BLHeli - S 4-in-1 ESC Dshot600 ready
Built-in BetaFlight OSD ( SPI control )
Built-in current meter ( max 14A, could be modified to 28A by replace resistor )
Built-in 5V 0.8A BEC with LC filter
Built-in voltage detection
BLHeli - S pass-through ready
Board size: 28.5 x 28.5mm
Board weight: 3.5g
Heading LED ready

Onboard 5A 4-in-1 ESC
Power supply: 1S LiPo / LiPo HV ( 4.2V / 4.35V )
Continuous current: 5A
Peak current: 6A ( 3 seconds )
BLHeli suite programmable
Factory firmware: O-L-5-REV16 - 6.HEX
Motor connector: JST PH1.25 3pin
Signal support: DShot150 / DShot300 / DShot600 / Oneshot125 / Multishot / PWM

Onboard Frsky Receiver Version
Compatible with both of Non EU and EU LBT transmitters
Channels: 8CH
Failsafe support: yes
No ground interference: 300m ( transmitter and receiver 1m from the ground )

Video Transmitter:
Output power: 25mW
Frequency: 48CH
With raceband: 5474 - 5945MHz
Input voltage: 3.3 - 5.5V
Current consumption: 300mA

700TVL Camera
Field of view: 120-degree
Video format: NTSC
Antenna: RG178 antenna
Size: 13.9 x 12.0mm ( L x W )
Weight: 3g

Includes:
1 x drone
1 x Crazybee F3 Flight control (built-in ESC, OSD, receiver, current sensor)
1 x 5.8g 48CH 25MW VTX +700TVL 1/4 CMOS camera
1 x USB charger
1 x screw driver
1 x propeller remover
4 x SE0703 KV19000 brushless motors
4 x 40mm cw/ccw 3-blade propellers

Requires:
1 x 1S Lipo battery (recommended type: 450mah, 30C, size: about 60x18x7mm)

* Battery is NOT included, we provided 2 compatible connectors with the kit.

Please explain:
Messages of this section are not monitored by HiModel, it is for review and discussion among customers only.

Upload Image:
(Up To 5 Files, only .jpg/.gif/.png files are accepted and sizes below 2MB for each)

Post as: Review Question

Select grade: star(s)

Anonymous: Yes No