THIS IS THE LATEST A3 SUPER II (VERSION 2)

• 32-bit MCU, 3-axis gyroscope and 3-axis accelerometer.
• One-click rescue, One-click hover.
• 6 flight modes: off, normal, 3D, auto-balance, auto-hover and user defined mode.
• 2 stick control modes: Manual Mode(MM) and Auto Mode(RR/AR).
• Various wing types: 1AIL+1ELE, 2AIL+1ELE, 1AIL+2ELE, 2AIL+2ELE, delta-wing and V-tail.
• Separated gain setting and gain rate for each flight mode, remote master gain control.
• Compatible with all standard receivers or Futaba's S.Bus/S.Bus single-line receiver.
• Up to 333Hz servo operating frequency, compatible with all analog and digital servos.
• 5-level response rate setting allows you to use it on gas-powered planes.
• H.V(7.4V) receivers and servos supported.
• Flat or upright mounting orientations.
• A program card helps you setting up the controller more easily in the field.
• New designed config GUI allows you upgrade the firmware online

Flight Mode

Gyro Off Mode Choose this mode to disable the gyros for all channels. The plane will be completely under the control of the radio. The plane will go back to its previous performance when operating it in this mode. Usually it is only used to test.

Normal Mode Normal mode is the most basic application of the gyro. In this mode, the gyro will sense angular velocity on each axis and make a momentary reaction. The normal mode is suitable for all types of fixed-wings, it can effectively improve the stability of your plane specially on a windy day.

3D AVCS Mode The AVCS mode is an advanced application of the gyro. By adding an integral algorithm to the gyros, the controller will try to lock the plane to its previous attitude if there is no command sent from the transmitter in a flight. This mode can effectively help you to accomplish such hard actions as hover and knife edge. But this mode is designed especially for the 3D planes, it's not suitable for the planes those not designed for 3D flight.

Auto-balance Mode The auto-balance mode is designed for the new beginners or the FPV applications. When operating in this mode, the controller will command the plane to maintain level flight automatically when you release the sticks. When switch it to this mode from any other modes in an emergency, the plane will recover to the level flight automatically, which we call "one-click rescue".

Auto-hover Mode The auto-hover mode is another form of the self balance ability of the controller. The only difference is that the correction from the gyro will be applied to both pitch and yaw axes, to keep the plane always vertical. When switch to this mode, the plane will lift its nose and start to hover automatically, which we call "one-click hover".

User Defined Mode This mode allows you to select different mode for each axis, from normal , 3D or gyro off mode.

Stick Control Mode

MM: Stick controls the servo directly.
RR: Stick controls the rotation rate on each axis.
AR: Stick controls the tilt angle rate on each axis.
① Whatever the setting of control mode is, the stick is always used to control the servo directly when operating in gyro off mode or the gyro of the corresponding axis has been disabled.
② Whatever the setting of control mode is, the stick is always used to control the rotation rate on each axis when operating in 3D mode.

Connection

The new A3 Super has 7 separated input channels and 5 output channels. You can use a standard receiver or a single-line receiver such as Futaba's S.Bus/S.Bus 2.

GUI

The new designed GUI helps you accomplish all settings of the controller and upgrade the firmware online.

EAGLE Aeroplane Flight Controller/ Stabilization System A3 Super II W/Programe card V2

• Main Controller: 32-bit MCU
• Sensor: 3-axis gyroscope and 3-axis accelerometer
• Gyroscope Scale Range: ±2000 dps
• Accelerometer Scale Range: ±4g
• Input Signal: Standard PPM with center point 1520uS, or S.Bus serial data
• Output Signal: PWM max frequency 333Hz, 1520±500uS
• Input Voltage: 4.8V ~ 7.4V
• Operating Temp: -10 ℃ ~ 50 ℃
• Size: 43×27×14mm
• Weight: 10g (excluding wires)