35Mhz Futaba 9CAP Super 9-Channel Synthesized Radio Control System W/R319DPS 3xS3001
    SKU 9CAP35S
    Brand Futaba
    Added 2008/05/06
    Updated 2008/05/17
     
    Tags: 35Mhz_Futaba_9CAP_Super_9-Channel_Synthesized_Radio_Control_System_W_R319DPS_3xS3001 

    Features:

    Transmitter:
    * Large graphic liquid-crystal display panel with 4 buttons and easy set up trun-and-press Dial for quick, easy setup.
    * All transmitters include all 3 aircraft types with specialized programming for each, including:
    - Airplane (ACRO)
    --V-tail
    --Elevon
    --Airbrake
    --Twin Aileron Servos (FLAPERON AND AIR-DIFF)
    --Gyro Mixing
    --Twin Elevator Servos (AILEVATOR)
    --Snap Roll ( 4 separate directions available)
    -Helicopter (6 swashplate types, including CCPM)(HELI)
    --3 Idel Ups
    --Throttle and Pitch Curvers per Condition
    --Gyro Mixing including separate settings per condition
    --Delay
    --Governor Mixing
    -Sailplane/Glider (3 wing types)(GLID)
    --V-tail
    --Twin ailerons (FLAPERON and AIL-DIFF)
    -- 4 flight conditions (NORM/OFFSET-1/2/3)(GLID2FL-C Only)
    --ELEVON
    --Crow (BUTTERFLY)
    --START OFFSET
    --SPEED OFFSET
    *BASIC menu for quick, easy set up of less complex models.
    *ADVANCE menu for more complex, unique setups.
    *Four electronic Trim Levers for rapid yet precise trim adjustment - no remembering to "store trims" between models and no more "bumped trims" during transport.
    *IDLE-DOWN (ACRO) and THR-CUT (ACRO/HELI) (engine shut off) setups to allow precise engine control for taxi and landings.
    *12 complete model memories with 6 more per optional CAMPac.
    *New stick design with improved feel, adjustable lenght and tension.
    *Triple rates available by setting dual rates to 3-position switches.
    *Eight Switches, 3 Dials and 2 Sliders; compeletely assignable in most applications.
    *Trainer system includes the "functional" (FUNC) setting, which allows the student to use the 9C super's mixing, helicopter, and other proramming functions even with a 4-channel buddy box.
    *Transmits in both FM(PPM) and PCM by selecting modulation/cycling transmitter. Requires receiver of proper modulation.
    *Permanent memory storage via EEPROM with no backup battery to service or have fail.
    *It features helicopter-friendly switch layout, with idle-up and throttle hold switches at the left hand, and a smooth, ratchet-less (unsprung) throttle for perfect hovering. Defaults to HELI(SW1) MODEL TYPE.
    *Change transmitter mode from mode 1 to modes 2,3 or 4.

    Specifications:

    Receiver Specification:
    Type: R319DPS synthesized
    Receiving frequency: 35Mhz
    Intermediate frep.: 10.7Mhz & 455 kHz
    Power requirement: 4.8V Ni-Cd battery
    Current drain: 40 mA
    Size: 1.27 x 2.17 x 0.80 in. (32.2 x 55.2 x 20.3 mm)
    Weight: 1.25 oz. (35.5 g)
    Channels: 9

    Includes/Requires:

    Includes:
    One Tx 9CAP-PCM (Only Model 1 available - throttle on right hand, but you can change it to Model 2 by yourself.)
    One Tx RF Synthesized Frequency Module FP-FSM
    One Rx FP-R319DPS Synthesized Rx (Dual Conversion, PCM1024)
    One RX Battery 600mAh
    One Tx Battery NT-8S700B 700mAh
    One Charger FBC-18C(4) (220V two round plug)
    One Mini switch harness with charge cord
    One Instruction manual ( English )
    One Tx Antenna
    Three S3001 Futaba servos

    Comments:

    * Note:
    we only sell the radio system in complete set, and do not sell the transmitter nor other components separately, so please do not ask.
    HiModel
    Back to computer version.
          Back
    Loading...