2.4G Futaba 9CHP Super 9ch Transmitter & R608FS Receiver (8ch) w/ RX,TX Batteries
    SKU 9CHP24
    Brand Futaba
    Added 2008/04/28
    Updated 2009/03/20
     
    Tags: 2.4G_Futaba_9CHP_Super_9ch_Transmitter_R608FS_Receiver_8ch_w_RXTX_Batteries 

    Features:

    Transmitter:
    * Large graphic liquid-crystal display panel with 4 buttons and easy set up trun-and-press Dial for quick, easy setup.
    * All transmitters include all 3 aircraft types with specialized programming for each, including:
    - Airplane (ACRO)
    --V-tail
    --Elevon
    --Airbrake
    --Twin Aileron Servos (FLAPERON AND AIR-DIFF)
    --Gyro Mixing
    --Twin Elevator Servos (AILEVATOR)
    --Snap Roll ( 4 separate directions available)
    -Helicopter (6 swashplate types, including CCPM)(HELI)
    --3 Idel Ups
    --Throttle and Pitch Curvers per Condition
    --Gyro Mixing including separate settings per condition
    --Delay
    --Governor Mixing
    -Sailplane/Glider (3 wing types)(GLID)
    --V-tail
    --Twin ailerons (FLAPERON and AIL-DIFF)
    -- 4 flight conditions (NORM/OFFSET-1/2/3)(GLID2FL-C Only)
    --ELEVON
    --Crow (BUTTERFLY)
    --START OFFSET
    --SPEED OFFSET
    *BASIC menu for quick, easy set up of less complex models.
    *ADVANCE menu for more complex, unique setups.
    *Four electronic Trim Levers for rapid yet precise trim adjustment - no remembering to "store trims" between models and no more "bumped trims" during transport.
    *IDLE-DOWN (ACRO) and THR-CUT (ACRO/HELI) (engine shut off) setups to allow precise engine control for taxi and landings.
    *12 complete model memories with 6 more per optional CAMPac.
    *New stick design with improved feel, adjustable lenght and tension.
    *Triple rates available by setting dual rates to 3-position switches.
    *Eight Switches, 3 Dials and 2 Sliders; compeletely assignable in most applications.
    *Trainer system includes the "functional" (FUNC) setting, which allows the student to use the 9C super's mixing, helicopter, and other proramming functions even with a 4-channel buddy box.
    *Transmits in both FM(PPM) and PCM by selecting modulation/cycling transmitter. Requires receiver of proper modulation.
    *Permanent memory storage via EEPROM with no backup battery to service or have fail.
    *It features helicopter-friendly switch layout, with idle-up and throttle hold switches at the left hand, and a smooth, ratchet-less (unsprung) throttle for perfect hovering. Defaults to HELI(SW1) MODEL TYPE.
    *Change transmitter mode from mode 1 to modes 2,3 or 4.


    Specifications:

    TM-8 RF moduel:
    ●Communication system: one-way communication
    ●Antenna: 1/2 wavelength di-pole
    ●Current consumption: 150mA maximum
    ●Setting switch for fail safe (F/S) setting and range check
    ●LED (light emitting diodes) indicate the operational status
    ●Area select: general/France

    R608FS Receiver:
    ●Dual antenna diversity
    ●Power requirement: 4.8V or 6.0V battery or regulated output from ESC, etc.
    ●F/S and battery F/S function for throttle channel (channel three)
    ●Size: 0.98 x 1.86 x 0.56 in. (24.9 x 47.3 x 14.3 mm)
    ●Weight: 0.48 oz. (13.5g)

    Includes/Requires:

    Includes:
    1 x Tx 9CHP super (Only Model 1 available - throttle on right hand, but you can change it to Model 2 by yourself.)
    1 x 2.4G FASST RF module TM-8
    1 x 2.4G Rx R608FS
    1 x RX Battery 1000mAh / 4.8V
    1 x Tx Battery NT-8S700B 700mAh
    1 x Charger FBC-18C(4) (220V two round plug)
    1 x Mini switch harness with charge cord
    1 x Instruction manual ( English )
    1 x Tx Antenna
    Back to computer version.
          Back
    Loading...